Optimizing FFF Process Parameters to Enhance PLA Performance on Low-Cost 3D Printers
Keywords:
Fused Filament Fabrication process, optimization, ANN, PSO, DOEAbstract
PLA (Polylactic Acid) is well known for its biodegradable properties and ease of use; however, a careful tuning of parameters such as infill density, layer height, feed rate, build orientation, and nozzle temperature is crucial to achieve the optimum strength and durability of the sample produced. While it has its own benefits, a low-cost FDM 3D printer often comes with limitations that affect the mechanical performance of printed parts, including calibration issues such as improper bed levelling, misaligned axes, and inconsistent extrusion, decreased temperature stability, and poorer build quality. To overcome these factors, a Design of Experiments (DoE) was applied using Response Surface Methodology (RSM). A total of 32 experiments were conducted to evaluate the influence of these parameters on tensile and flexural strength. In addition, a hybrid optimization technique combining Artificial Neural Network (ANN) and Particle Swarm Optimization (PSO) was applied. ANN determined strength predictions, whereas PSO was employed to yield the best parameter setups. The maximum tensile strength and flexural strength achieved 34.48 MPa and 71.07 MPa, respectively, indicating considerable enhancements in the mechanical traits of PLA prints. This study shows that with proper process parameter optimization, the performance of PLA can be increased even using low-cost printers.
References
[1] K V Wong and A. Hernandez, "A review of additive manufacturing," International scholarly research notices, vol. 2012, no.1, pp. 208760, 2012.
[2] S. Vyavahare, "Fused deposition modelling: a review," Rapid Prototyping Journal, vol.26, no.1, pp. 176-201, 2020.
[3] R B Kristiawan, "A review on the fused deposition modeling (FDM) 3D printing: Filament processing, materials, and printing parameters," Open Engineering, vol. 11, no.1, pp. 639-649, 2021.
[4] E H Tümer and H.Y. Erbil, "Extrusion-based 3D printing applications of PLA composites: a review," Coatings, vol. 11, no.4, pp. 390,
2021.
[5] A. Kantaros and D. Piromalis, "Employing a low-cost desktop 3D printer: Challenges, and how to overcome them by tuning key process parameters," International Journal of Mechanics and Applications, vol. 10, no.1, pp. 11-19, 2021.
[6] A. Qattawi, "Investigating the effect of fused deposition modeling processing parameters using Taguchi design of experiment method," Journal of Manufacturing Processes, vol.36, pp. 164-174, 2018.
[7] S. Anand and M. Satyarthi, "Parametric Optimization of Fused Filament Fabrication Process," in International Conference on Mechanical and Energy Technologies, 2021.
[8] S. Anand and M.K. Satyarthi, "Neural network-based modeling of FFF process for PET-G: Evaluating MLPNN and RBFNN performance in mechanical property prediction," Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, pp. 09544089241272752, 2024.
[9] AJ. Sheoran and H. Kumar, "Fused Deposition modeling process parameters optimization and effect on mechanical properties and part quality: Review and reflection on present research," Materials Today: Proceedings, vol.21, pp. 1659-1672, 2020.
[10] J. Giri, "Optimization of FDM process parameters for dual extruder 3d printer using Artificial Neural network," Materials Today: Proceedings, vol. 43, pp. 3242-3249, 2021.
[11] J.M. Chacón, "Additive manufacturing of PLA structures using fused deposition modelling: Effect of process parameters on mechanical properties and their optimal selection," Materials & Design, vol.124, pp. 143-157, 2017.
[12] V B Nidagundi, R. Keshavamurthy and C. Prakash, "Studies on parametric optimization for fused deposition modelling process," Materials Today: Proceedings, vol. 2, no.4-5, pp. 1691-1699, 2015.
[13] J B Song, B. Wang and X. Hao, "Optimization Algorithms and Their Applications and Prospects in Manufacturing Engineering," Materials, vol. 17, no.16, pp. 4093, 2014.
[14] Zaman, "Impact of fused deposition modeling (FDM) process parameters on strength of built parts using Taguchi’s design of experiments," The international journal of Advanced Manufacturing technology, vol.101, pp. 1215-1226, 2019.
[15] S Anand, G. Dhankhar and M.K. Satyarthi, "Optimizing mechanical properties of PETG fabricated parts via PSO-BFO hybrid algorithm in fused deposition modelling," International Journal on Interactive Design and Manufacturing (IJIDeM), pp. 1-17, 2025.
[16] A. Qattawi, B. Alrawi and A. Guzman, "Experimental optimization of fused deposition modelling processing parameters: a design-for-manufacturing approach," Procedia Manufacturing, vol. 10, pp. 791-803, 2017.
[17] E. Behazin, M. Misra and A.K. Mohanty, "Compatibilization of toughened polypropylene/biocarbon biocomposites: A full factorial design optimization of mechanical properties," Polymer Testing, vol.61, pp. 364-372, 2017.
[18] Heidari-Rarani, "Optimization of FDM process parameters for tensile properties of polylactic acid, specimens using Taguchi design of experiment method," Journal of Thermoplastic Composite Materials, vol.35, no.12, pp. 2435-2452, 2022.
[19] Srinivasa Sai Abhijit Challapalli, "Optimizing Dallas-Fort Worth Bus Transportation System Using Any Logic," Journal of Sensors, IoT & Health Sciences, vol.2, no.4, pp.40-55, 2024.
[20] Chelladurai, "Optimization of process parameters using response surface methodology: A review," Materials Today: Proceedings, vol.37, pp. 1301-1304, 2021.
[21] Tayyab, "Prediction of mechanical properties for acrylonitrile-butadiene-styrene parts manufactured by fused deposition modelling using artificial neural network and genetic algorithm," International Journal of Computer Integrated Manufacturing, vol. 36, no.9, pp. 1295-1312, 2023.
[22] M S Saad, "Modelling and evolutionary computation optimization on FDM process for flexural strength using integrated approach RSM and PSO," Progress in Additive Manufacturing, vol. 6, pp. 143-154, 2021.
[23] Srinivasa Sai Abhijit Challapalli, "Sentiment Analysis of the Twitter Dataset for the Prediction of Sentiments," Journal of Sensors, IoT & Health Sciences, vol.2, no.4, pp.1-15, 2024.
[24] M.Z. Zakaria, "ANN-PSO Modelling and Optimization to Reduce Surface Roughness in Additive Manufactured Sports Equipment," in International Conference on Innovation and Technology in Sports, 2023.
[25] V C Boppana and F. Ali, "Improvement of tensile strength of fused deposition modelling (FDM) part using artificial neural network and genetic algorithm techniques," International Journal of Industrial Engineering and Operations Management, vol. 6, no.2, pp. 117-142, 2024.
[26] S Dhinesh, "Study on flexural and tensile behavior of PLA, ABS and PLA-ABS materials," Materials Today: Proceedings, vol.45, pp. 1175-1180, 2021.
[27] S J Bardiya, J. Jerald and V. Satheeshkumar, "The impact of process parameters on the tensile strength, flexural strength and the manufacturing time of fused filament fabricated (FFF) parts," Materials Today: Proceedings, vol.39, pp. 1362-1366, 2021.
[28] M J Anderson and P.J. Whitcomb, "RSM simplified: optimizing processes using response surface methods for design of experiments," Productivity press, 2016.
[29] J Kennedy and R. Eberhart, "Particle swarm optimization," in Proceedings of ICNN'95-international conference on neural networks, 1995.
[30] A. Nickabadi, M.M. Ebadzadeh and R. Safabakhsh, "A novel particle swarm optimization algorithm with adaptive inertia weight," Applied soft computing, vol.11, no.4, pp. 3658-3670, 2024
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Journal of Electronics and Power Engineering (JEPE)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Fringe Global Scientific Press publishes all the papers under a Creative Commons Attribution-Non-Commercial 4.0 International (CC BY-NC 4.0) (https://creativecommons.org/licenses/by-nc/4.0/) license. Authors have the liberty to replicate and distribute their work. Authors have the ability to use either the whole or a portion of their piece in compilations or other publications that include their own work. Please see the licensing terms for more information on reusing the work.
